Garage Door Sensor, Remote & Keypad Repair Tallahassee, FL
Door reverses, won't close, or the remote and keypad stopped working? Most of these are quick fixes.
What the Safety Sensors Do and Why Doors Reverse
The two small "eyes" near the bottom of the tracks send an invisible beam across the doorway. If something breaks that beam while the door is closing, the opener stops and reverses. Under the UL 325 safety standard those eyes have to be mounted no higher than 6 inches above the garage floor, so they protect people and pets and not just cars, and the standard also calls for the door to reverse when it touches a 1.5 inch object on the floor.
When the eyes are dirty, knocked out of line or blocked, the door acts as if something is in the way. That is the cause of most "door goes down and comes back up" calls, and it is also why a door that was fine yesterday can misbehave after a storm. Our opener repair page, garage door opener repair, covers the opener itself.
Sensor, Remote and Keypad Problems We Fix
Door reverses before it closes
Usually dirty, blocked or misaligned sensor eyes, or damaged wiring to them.
Opener light blinks and the door will not close
The opener is telling you it cannot see the sensor beam.
Remote only works close to the garage
Weak batteries, a failing remote or a problem with the opener receiver.
Keypad is dead or ignores the code
Dead battery, moisture in the keypad or a code that has to be reprogrammed.
Remotes quit after a power outage
Some openers lose remote programming and need to be re-paired.
Smart opener lost its connection
The opener has dropped off Wi-Fi and needs to be reconnected, not replaced.
What Throws Sensors Off in Tallahassee
Spring in Tallahassee means pollen. Oak, pine and juniper are the main sources, and pine pollen leaves the yellow film that coats cars and outdoor surfaces. That film settles on sensor lenses as well, and a coated lens can lose the beam. Wasps and mud daubers are active in our area, and mud nests on sheltered spots around buildings can interfere with small mechanical and electronic devices. A sensor eye mounted low at the side of a door can be an inviting spot to build, so a quick look and a wipe-down at the start of each season helps.
Summer thunderstorms and wind can bump the eyes out of line, and a heavy rain can get moisture into an outdoor keypad. After the multi-day power outages we have seen from storms like Hermine, Michael and Idalia, remotes and keypads sometimes need re-pairing. If the door only works from the wall button after a storm, read our storm preparation guide for what to check.
How We Fix and Test the Door
We clean and realign the eyes, check the wiring along its full length for pinches or lawn-equipment damage, and confirm the eyes are mounted at the right height. Remotes and keypads get fresh batteries and are re-paired, or replaced if they are failing, and smart openers are reconnected to your network. Then we test it the way the industry recommends: block the beam and confirm the door will not close, and put an object in the door's path to confirm it reverses. You can repeat those tests monthly.
If the problem turns out to be the opener's circuit board or receiver, we will tell you before replacing anything and quote the repair or a new unit. See opener replacement if the opener is past repairing.
Can I bypass or disable the sensors to get the door working?
Please don't. The sensors are a required safety feature that keeps people and pets from being caught under a closing door. If they are misbehaving, the fix is to clean, realign or repair them, which is usually quick.
Related Garage Door Repairs
If the sensors are fine, the cause may be elsewhere. See opener repair, off-track door repair or our Florida maintenance checklist, which includes the monthly sensor test.
Sensor, Remote & Keypad Questions
Almost always the safety sensors. A dirty lens, something in the beam path or a slight misalignment makes the opener think the doorway is blocked, so it reverses. Less often a binding track or the force setting is the cause.
On most openers a blinking light after you press close means the sensors are misaligned, blocked or disconnected. Wipe the lenses, check that both eyes face each other and look for a damaged wire.
Usually not. Dead batteries, lost programming or a failing remote are far more common than an opener receiver failure.
Monthly. Block the beam while the door is closing, or place an object in its path, and confirm that the door reverses.